turbines

WE Handbook- 2- Aerodynamics and Loads
Wind Turbine Blade Aerodynamics
Wind turbine blades are shaped to generate the maximum power from the wind at
the minimum cost. Primarily the design is driven by the aerodynamic requirements,
but economics mean that the blade shape is a compromise to keep the cost of construction reasonable. In particular, the blade tends to be thicker than the aerodynamic
optimum close to the root, where the stresses due to bending are greatest.
The blade design process starts with a “best guess” compromise between aerodynamic and structural efficiency. The choice of materials and manufacturing process
will also have an influence on how thin (hence aerodynamically ideal) the blade can
be built. For instance, prepreg carbon fibre is stiffer and stronger than infused glass
fibre. The chosen aerodynamic shape gives rise to loads, which are fed into the structural design. Problems identified at this stage can then be used to modify the shape if
necessary and recalculate the aerodynamic performance.
The Wind
It might seem obvious, but an understanding of the wind is fundamental to wind
turbine design. The power available from the wind varies as the cube of the wind
speed, so twice the wind speed means eight times the power. This is why sites have
to be selected carefully: below about 5m/s ( 0mph) wind speed there is not sufficient
power in the wind to be useful. Conversely, strong gusts provide extremely high
levels of power, but it is not economically viable to build machines to be able to make
the most of the power peaks as their capacity would be wasted most of the time. So
the ideal is a site with steady winds and a machine that is able to make the most of
the lighter winds whilst surviving the strongest gusts.
As well as varying day-to-day, the wind varies every second due to turbulence caused
by land features, thermals and weather. It also blows more strongly higher above
the ground than closer to it, due to surface friction. All these effects lead to varying
loads on the blades of a turbine as they rotate, and mean that the aerodynamic and
structural design needs to cope with conditions that are rarely optimal.
By extracting power, the turbine itself has an effect on the wind: downwind of the
turbine the air moves more slowly than upwind. The wind starts to slow down even
before it reaches the blades, reducing the wind speed through the “disc” (the imaginary circle formed by the blade tips, also called the swept area) and hence reducing
the available power. Some of the wind that was heading for the disc diverts around
the slower-moving air and misses the blades entirely. So there is an optimum amount
of power to extract from a given disc diameter: try to take too much and the wind will
slow down too much, reducing the available power. In fact the ideal is to reduce the
wind speed by about two thirds downwind of the turbine, though even then the wind
just before the turbine will have lost about a third of its speed. This allows a theoretical maximum of 59% of the wind’s power to be captured (this is called Betz’s limit).
In practice only 40-50% is achieved by current designs.WE Handbook- 2- Aerodynamics and Loads 2
Number of blades
The limitation on the available power in the wind means that the more blades there
are, the less power each can extract. A consequence of this is that each blade must
also be narrower to maintain aerodynamic efficiency. The total blade area as a fraction
of the total swept disc area is called the solidity, and aerodynamically there is an
optimum solidity for a given tip speed; the higher the number of blades, the narrower each one must be. In practice the optimum solidity is low (only a few percent)
which means that even with only three blades, each one must be very narrow. To slip
through the air easily the blades must be thin relative to their width, so the limited
solidity also limits the thickness of the blades. Furthermore, it becomes difficult to
build the blades strong enough if they are too thin, or the cost per blade increases
significantly as more expensive materials are required.
For this reason, most large machines do not have more than three blades. The other
factor influencing the number of blades is aesthetics: it is generally accepted that
three-bladed turbines are less visually disturbing than one- or two-bladed designs.
How blades capture wind power
Just like an aeroplane wing, wind turbine blades work by generating lift due to their
shape. The more curved side generates low air pressures while high pressure air
pushes on the other side of the aerofoil. The net result is a lift force perpendicular to
the direction of flow of the air.
The lift force increases as the blade is turned to present itself at a greater angle to
the wind. This is called the angle of attack. At very large angles of attack the blade
“stalls” and the lift decreases again. So there is an optimum angle of attack to generate the maximum lift.
Lift & drag vectorsWE Handbook- 2- Aerodynamics and Loads
There is, unfortunately, also a retarding force on the blade: the drag. This is the force
parallel to the wind flow, and also increases with angle of attack. If the aerofoil shape
is good, the lift force is much bigger than the drag, but at very high angles of attack,
especially when the blade stalls, the drag increases dramatically. So at an angle
slightly less than the maximum lift angle, the blade reaches its maximum lift/drag
ratio. The best operating point will be between these two angles.
Since the drag is in the downwind direction, it may seem that it wouldn’t matter for a
wind turbine as the drag would be parallel to the turbine axis, so wouldn’t slow the rotor
down. It would just create “thrust”, the force that acts parallel to the turbine axis hence
has no tendency to speed up or slow down the rotor. When the rotor is stationary
(e.g. just before start-up), this is indeed the case. However the blade’s own movement
through the air means that, as far as the blade is concerned, the wind is blowing from
a different angle. This is called apparent wind. The apparent wind is stronger than the
true wind but its angle is less favourable: it rotates the angles of the lift and drag to
reduce the effect of lift force pulling the blade round and increase the effect of drag
slowing it down. It also means that the lift force contributes to the thrust on the rotor.
The result of this is that, to maintain a good angle of attack, the blade must be turned
further from the true wind angle.
Apparent wind angles
Blade at low, medium & high angles of attackWE Handbook- 2- Aerodynamics and Loads 4
Twist
The closer to the tip of the blade you get, the faster the blade is moving through the
air and so the greater the apparent wind angle is. Thus the blade needs to be turned
further at the tips than at the root, in other words it must be built with a twist along its
length. Typically the twist is around 0-20° from root to tip. The requirement to twist
the blade has implications on the ease of manufacture.
Blade section shape
Apart from the twist, wind turbine blades have similar requirements to aeroplane
wings, so their cross-sections are usually based on a similar family of shapes. In
general the best lift/drag characteristics are obtained by an aerofoil that is fairly thin:
it’s thickness might be only 0- 5% of its “chord” length (the length across the blade,
in the direction of the wind flow).
Blade twist
Typical aerofoil shapes offering good lift/drag ratioWE Handbook- 2- Aerodynamics and Loads 5
If there were no structural requirements, this is how a wind turbine blade would be
proportioned, but of course the blade needs to support the lift, drag and gravitational
forces acting on it. These structural requirements generally mean the aerofoil needs
to be thicker than the aerodynamic optimum, especially at locations towards the
root (where the blade attaches to the hub) where the bending forces are greatest.
Fortunately that is also where the apparent wind is moving more slowly and the blade
has the least leverage over the hub, so some aerodynamic inefficiency at that point is
less serious than it would be closer to the tip. Having said this, the section can’t get
too thick for its chord length or the air flow will “separate” from the back of the blade
– similar to what happens when it stalls – and the drag will increase dramatically.
To increase thickness near the root without creating a very short, fat, aerofoil section,
some designs use a “flatback” section. This is either a standard section thickened
up to a square trailing (back) edge, or a longer aerofoil shape that has been truncated.
This reduces the drag compared to a rounder section, but can generate more noise so
its suitability depends on the wind farm site.
There is a trade-off to be made between aerodynamic efficiency and structural efficiency: even if a thin blade can be made strong and stiff enough by using lots of
reinforcement inside, it might still be better to make the blade a bit thicker (hence
less aerodynamically efficient) if it saves so much cost of material that the overall
cost of electricity is reduced. The wind is free after all; it’s only the machine that we
have to pay for. So there is inevitably some iteration in the design process to find the
optimum thickness for the blade.
Blade planform shape
The planform shape is chosen to give the blade an approximately constant slowing
effect on the wind over the whole rotor disc (i.e. the tip slows the wind to the same
degree as the centre or root of the blade). This ensures that none of the air leaves the
turbine too slowly (causing turbulence), yet none is allowed to pass through too fast
(which would represent wasted energy). Remembering Betz’s limit discussed above,
this results in the maximum power extraction.
Typical “flatback” aerofoil shapeWE Handbook- 2- Aerodynamics and Loads
Because the tip of the blade is moving faster than the root, it passes through more
volume of air, hence must generate a greater lift force to slow that air down enough.
Fortunately, lift increases with the square of speed so its greater speed more than
allows for that. In reality the blade can be narrower close to the tip than near the
root and still generate enough lift. The optimum tapering of the blade planform as it
goes outboard can be calculated; roughly speaking the chord should be inverse to the
radius. So if the chord was 2m at 0m radius, it should be 0m at m radius.
This relationship breaks down close to the root and tip, where the optimum shape
changes to account for tip losses.
In reality a fairly linear taper is sufficiently close to the optimum for most designs,
structurally superior and easier to build than the optimum shape.
Rotational speed
The speed at which the turbine rotates is a fundamental choice in the design, and is
defined in terms of the speed of the blade tips relative to the “free” wind speed (i.e.
before the wind is slowed down by the turbine). This is called the tip speed ratio.
High tip speed ratio means the aerodynamic force on the blades (due to lift and drag)
is almost parallel to the rotor axis, so relies on a good lift/drag ratio. The lift/drag ratio
can be affected severely by dirt or roughness on the blades.
Optimum blade planformWE Handbook- 2- Aerodynamics and Loads
Low tip speed ratio would seem like a better choice but unfortunately results in lower
aerodynamic efficiency, due to two effects. Because the lift force on the blades
generates torque, it has an equal but opposite effect on the wind, tending to push
it around tangentially in the other direction. The result is that the air downwind of
the turbine has “swirl”, i.e. it spins in the opposite direction to the blades. That swirl
represents lost power so reduces the available power that can be extracted from the
wind. Lower rotational speed requires higher torque for the same power output, so
lower tip speed results in higher wake swirl losses.
Effect of tip speed ratio on sensitivity to drag
Swirl in the wakeWE Handbook- 2- Aerodynamics and Loads
The other reduction in efficiency at low tip speed ratio comes from tip losses, where
high-pressure air from the upwind side of the blade escapes around the blade tip
to the low-pressure side, thereby wasting energy. Since power = force x speed, at
slower rotational speed the blades need to generate more lift force to achieve the
same power. To generate more lift for a given length the blade has to be wider, which
means that, geometrically speaking, a greater proportion of the blade’s length can be
considered to be close to the tip. Thus more of the air contributes to tip losses and
the efficiency decreases. Various techniques can be used to limit tip losses such as
winglets (commonly seen on airliners) but few are employed in practice owing to their
additional cost.
The higher lift force on a wider blade also translates to higher loads on the other components such as the hub and bearings, so low tip speed ratio will increase the cost of
these items. On the other hand the wide blade is better able to carry the lift force (as
discussed previously), so the blade itself may be cheaper.
All this means that turbine designers typically compromise on tip speed ratios in the
region of - 0, so at design wind speed (usually 2- 5 metres per second) the blade
tip can be moving at around 20 m/s (approximately 2 0 miles per hour). There are
practical limits on the absolute tip speed too: at these speeds, bird impacts and rain
erosion start to become a problem for the longevity of the blades and noise increases
dramatically with tip speed.
Power and pitch control
For an economical design, the maximum performance of the generator and gearbox
need to be limited to an appropriate level for the turbines operating environment. The
ideal situation is for the turbine to be able to extract as much power as possible from
the wind up to the rated power of the generator, then limit the power extraction at
that level as the wind increases further.
Turbine Power CurveWE Handbook- 2- Aerodynamics and Loads 9
If the blades’ angle is kept constant, the turbine is unable to respond to changes in
wind speed. Not only does this make it impossible to maintain an optimum angle
of attack to generate the maximum power at varying wind speeds, the only way
to “depower” the machine in high wind speeds is by relying on the blades to stall
(known as passive stall control). This doesn’t give the perfectly flat power curve
above the rated wind speed shown in the graph above, so to limit the maximum
power, a passive stall-controlled turbine will usually be operating somewhat below
its maximum potential.
If instead the blades are attached via a bearing that allows the angle of attack to be
varied (active pitch control), the blades can be angled to maintain optimum efficiency
right up to the design wind speed (at which the generator is producing its rated
output). Above that wind speed they can be “feathered”, i.e. rotated in pitch to
decrease their angle of attack and hence their lift, so controlling the power. In survival
conditions, the turbine can be stopped altogether and the blades feathered to produce
no turning force at all.
An alternative to decreasing the angle of attack above the design wind speed is
deliberately to increase it to the point where the blade stalls (active stall control). This
decreases lift and increases drag, so has the desired slowing effect on blade rotation.
It is also less sensitive to gusts of wind than feathering: by decreasing the apparent
wind angle, gusts increase the angle of attack so tend to make the blade stall more.
Therefore controlling blade speed by stall rather than feathering can be beneficial in
gusty conditions. Both methods are used by different designs.
In Summary
n Length: The blade length determines how much wind power can be captured,
according to the “swept area” of the rotor disc. Of all the energy in the wind,
only about half can realistically be extracted (Betz’s limit).
n Aerodynamic Section: The blades have an aerodynamic profile in cross section to
create lift and rotate the turbine.
n Planform Shape: The planform shape gets narrower to towards the tip to maintain
a constant slowing effect across the swept area. This ensures that none of the
air leaves the turbine too slowly (causing turbulence), yet none is allowed to pass
through too fast (which would represent wasted energy).
n Aerofoil Thickness: The thickness increases towards the root to take the structural
loads, in particular the bending moments. If loads weren’t important then the
section thickness/chord ratio would be about 0- 5% along the whole length.
“Flatback” sections may be used near the root to improve aerodynamic efficiency.WE Handbook- 2- Aerodynamics and Loads 0
n Blade Twist: The apparent wind angle changes along the blade due to the increase
in blade speed with increasing distance outboard. Hence to maintain optimum
angle of attack of the blade section to the wind, it must be twisted along its
length.
n Blade Number and Rotational Speed: Typically the rotational speed chosen so that
the tips are moving at seven to ten times the wind speed, and there are usually
no more than three blades.
- Higher speeds and higher numbers of blades mean each blade must be
narrower, hence thinner, which makes it harder to make them strong
enough.At very high rotational speeds the blades also start to become
aerodynamically inefficient, noisy and prone to erosion and bird strikes.
- At low rotational speeds, swirl in the wake and tip losses reduce efficiency,
while thrust loads on the other components increase.
n Pitch Control: Because the wind power varies so greatly (with the cube of wind
speed), the turbine must be able to generate power in light winds and withstand
the loads in much stronger winds. Therefore, above the optimum wind speed, the
blades are typically pitched either into the wind (feathering) or away from the wind
(active stall) to reduce the generated power and regulate the loads.

WIND

42 cm x 29.7 cm (Non-Bleed)
42.6 cm x 30.3 cm (Bleed)
3
1600
1400
1200
1000
800
600
400
200
4 5 6 7 8 9 10 11 12 13 14 15 16 17
Wind Speed (m/s)
S82-1.5 MW
Power curve
Power (kW)
18 19 20
MODEL S82-1500kW
OPERATING DATA
Rated power 1500 kW
Cut-in wind speed 4 m/s
Rated wind speed 14 m/s
Cut-off wind speed 20 m/s
Survival wind speed 52.5 m/s
ROTOR
Type 3 Blades, Upwind / Horizontal axis
Diameter 82 m
Rotational speed at rated power 15.6 to 18.4 rpm
Rotor blade material Epoxy bonded fiber glass
Swept area 5281 m2
Power regulation Active pitch regulated with Suzlon Flexi Slip System
GEARBOX
Type 1 planetary stage / 2 helical stages
Ratio 1 : 95.09
Nominal load 1650 kW
Type of cooling Forced oil cooling lubrication system
GENERATOR
Type Single speed induction generator with slip rings, variable rotor resistance via Suzlon Flexi slip system
Speed at rated power 1511 rpm
Rated power 1500 kW
Rated voltage 690 V AC (phase to phase)
Frequency 50 Hz
Insulation Class H
Enclosure IP 54 / IP 23 (slip ring unit)
Cooling system Air cooled
TOWER
Type Tubular tower (corrision proof painting on inner and outer surface) with welded steel plates
Tower height 76 m
Hub height (including foundation) Aproximately 78.5 m
BRAKING SYSTEM
Aerodynamic braking 3 Independent systems with blade pitching
Mechanical braking Hydraulic fail safe disk brake system
YAW SYSTEM
Type Active electrical yaw motor
Bearing Polyamide Slide bearing with gear ring & automatic greasing system
Protection Cable twist sensor, proximity sensor
PITCH SYSTEM
Type 3 independent blade pitch control with battery backup for each blade
Operating range -5 º to +90 º
Resolution 0.1 to 10 Deg
CONTROLLER Suzlon Control System with following salient features:
- Park slave
- Power output control / limitation
- Reactive power control
- Grid measurement
- Low voltage ride through (LVRT)
- Weather measurement
- Time synchronization
- Statistics
Wind Class III a
Certification & Standards GL (T-GL-009A-2007)
Quality System ISO 9001:2000
S82-1.5
World’s 5th largest and fastest growing integrated wind turbine manufacturer | 600 kW to 2.1 MW capacity wind turbines | Workforce of 14,000 people and a global presence in
21 countries across 5 continents | Manufacturing units in 3 continents | R&D facilities in Germany and The Netherlands
S82-1.5 MW is designed for generating the optimal power
output even at sites with a modest wind speed regime. The
wind turbine concept is based on robust design with pitch
regulated blade operation, a 3-stage gearbox with 1650 kW
rating and flexible coupling to the asynchronous induction
generator. The Suzlon Flexi-slip System provides efficient
control of the load and power control. The turbine operation
is efficiently controlled by the Suzlon controller. These
technologies are all well-known in the wind power industry
and have proven themselves. The S82-1.5 MW is designed to
withstand extreme conditions and operate effectively with low
maintenance cost.
BLADES
As all other Suzlon blades, the AE40 blade is a fully integrated
design. The blade manufacturing system from mould
engineering to state-of-the-art Resin Infusion Moulding (RIM) is
done in close co-operation between the Dutch design team
and the manufac-turing plants in India and China.
PITCH SYSTEM
The full-span blade pitching system is based on electrical
motors with individual power backup which allows fast and
efficient pitching of the blades. With a resolution of 0.1° and a
special fast-pitching mode, the S82-1.5 MW allows optimal
power output as well as fast and safe braking of the rotor.
GEARBOX
The design of the gearbox has always been given special
attentionin Suzlon. The design philosophy is based on years of
experience with wind turbines in harsh environments and the
internal design standard well exceeds the industry standards.
The power rating of the gearbox for the S82-1.5 MW is
actually 1.65 MW. With the recent acquisition of Hansen
Transmission, Suzlon will also in the future secure in-house
design and development of superior gearbox technology for
the customer ’s benefit.
SERVICE AND MAINTENANCE
Suzlon has teams of trained wind farm technicians around the
globe who focus on excellence in service, maintenance and
monitoring. Our service technicians aim to maximise energy
production from the wind, and ensure the turbines operate
reliably and with minimal maintenance costs during their life
span. The key emphasis is on maximizing availability and
efficiency in operation thus providing ease of mind for our
clients. Suzlon provides intensive and continuous training
programs for its wind farm technicians, both in and out of field
and complement our own training resources by using highly
respected and reputable industry training consultants to tutor
and train our technicians and technical support engineers.
MANUFACTURING
Suzlon's manufacturing facilities for wind turbine generator
components and rotor blades are currently located in India,
China, Belgium and the USA. As part of Suzlon's strategic
growth plans to significantly increase manufacturing capacity of
all key turbine components, a number of new facilities are
currently planned or under construction. This meets our
objective to vertically integrate the entire supply chain,
ensuring that Suzlon brings to the market the most cost
efficient and reliable technology. It also enables us to control
the supply chain to secure quality, volume and growth, as well
as deliver long term service support.
END TO END SOLUTIONS SINCE 1995
The End-to-End solution pattern is built on Suzlon’s expertise
in technology, processes and thorough understanding of the
wind energy market. It is a unique combination of proven
technology and a bundle of value added services. Under this
successful and proven business model, Suzlon undertakes the
complete turn-key responsibility - from arranging land; to
equipment supply & EPC; to nodal agency clearances; to
life-cycle operations & maintenance of projects. Customers
therefore do not have to engage extra manpower for their
wind projects. Suzlon brought about a paradigm shift in the
wind energy market with the End-to-End solutions. It made
setting up wind energy projects simple, hassle-free and
enabled hundreds of customers including small/medium/big
enterprises, Indian and multinational corporates, public sector
companies and even individuals set-up their own wind energy
projects with confidence and ease.
Under given set of parameter and conditions.
Subject to change without notice due to difference in parameters, conditions and/or change in equipment or technological requirements.42 cm x 29.7 cm (Non-Bleed)
42.6 cm x 30.3 cm (Bleed)
3
1600
1400
1200
1000
800
600
400
200
4 5 6 7 8 9 10 11 12 13 14 15 16 17
Wind Speed (m/s)
S82-1.5 MW
Power curve
Power (kW)
18 19 20
MODEL S82-1500kW
OPERATING DATA
Rated power 1500 kW
Cut-in wind speed 4 m/s
Rated wind speed 14 m/s
Cut-off wind speed 20 m/s
Survival wind speed 52.5 m/s
ROTOR
Type 3 Blades, Upwind / Horizontal axis
Diameter 82 m
Rotational speed at rated power 15.6 to 18.4 rpm
Rotor blade material Epoxy bonded fiber glass
Swept area 5281 m2
Power regulation Active pitch regulated with Suzlon Flexi Slip System
GEARBOX
Type 1 planetary stage / 2 helical stages
Ratio 1 : 95.09
Nominal load 1650 kW
Type of cooling Forced oil cooling lubrication system
GENERATOR
Type Single speed induction generator with slip rings, variable rotor resistance via Suzlon Flexi slip system
Speed at rated power 1511 rpm
Rated power 1500 kW
Rated voltage 690 V AC (phase to phase)
Frequency 50 Hz
Insulation Class H
Enclosure IP 54 / IP 23 (slip ring unit)
Cooling system Air cooled
TOWER
Type Tubular tower (corrision proof painting on inner and outer surface) with welded steel plates
Tower height 76 m
Hub height (including foundation) Aproximately 78.5 m
BRAKING SYSTEM
Aerodynamic braking 3 Independent systems with blade pitching
Mechanical braking Hydraulic fail safe disk brake system
YAW SYSTEM
Type Active electrical yaw motor
Bearing Polyamide Slide bearing with gear ring & automatic greasing system
Protection Cable twist sensor, proximity sensor
PITCH SYSTEM
Type 3 independent blade pitch control with battery backup for each blade
Operating range -5 º to +90 º
Resolution 0.1 to 10 Deg
CONTROLLER Suzlon Control System with following salient features:
- Park slave
- Power output control / limitation
- Reactive power control
- Grid measurement
- Low voltage ride through (LVRT)
- Weather measurement
- Time synchronization
- Statistics
Wind Class III a
Certification & Standards GL (T-GL-009A-2007)
Quality System ISO 9001:2000
S82-1.5
World’s 5th largest and fastest growing integrated wind turbine manufacturer | 600 kW to 2.1 MW capacity wind turbines | Workforce of 14,000 people and a global presence in
21 countries across 5 continents | Manufacturing units in 3 continents | R&D facilities in Germany and The Netherlands
S82-1.5 MW is designed for generating the optimal power
output even at sites with a modest wind speed regime. The
wind turbine concept is based on robust design with pitch
regulated blade operation, a 3-stage gearbox with 1650 kW
rating and flexible coupling to the asynchronous induction
generator. The Suzlon Flexi-slip System provides efficient
control of the load and power control. The turbine operation
is efficiently controlled by the Suzlon controller. These
technologies are all well-known in the wind power industry
and have proven themselves. The S82-1.5 MW is designed to
withstand extreme conditions and operate effectively with low
maintenance cost.
BLADES
As all other Suzlon blades, the AE40 blade is a fully integrated
design. The blade manufacturing system from mould
engineering to state-of-the-art Resin Infusion Moulding (RIM) is
done in close co-operation between the Dutch design team
and the manufac-turing plants in India and China.
PITCH SYSTEM
The full-span blade pitching system is based on electrical
motors with individual power backup which allows fast and
efficient pitching of the blades. With a resolution of 0.1° and a
special fast-pitching mode, the S82-1.5 MW allows optimal
power output as well as fast and safe braking of the rotor.
GEARBOX
The design of the gearbox has always been given special
attentionin Suzlon. The design philosophy is based on years of
experience with wind turbines in harsh environments and the
internal design standard well exceeds the industry standards.
The power rating of the gearbox for the S82-1.5 MW is
actually 1.65 MW. With the recent acquisition of Hansen
Transmission, Suzlon will also in the future secure in-house
design and development of superior gearbox technology for
the customer ’s benefit.
SERVICE AND MAINTENANCE
Suzlon has teams of trained wind farm technicians around the
globe who focus on excellence in service, maintenance and
monitoring. Our service technicians aim to maximise energy
production from the wind, and ensure the turbines operate
reliably and with minimal maintenance costs during their life
span. The key emphasis is on maximizing availability and
efficiency in operation thus providing ease of mind for our
clients. Suzlon provides intensive and continuous training
programs for its wind farm technicians, both in and out of field
and complement our own training resources by using highly
respected and reputable industry training consultants to tutor
and train our technicians and technical support engineers.
MANUFACTURING
Suzlon's manufacturing facilities for wind turbine generator
components and rotor blades are currently located in India,
China, Belgium and the USA. As part of Suzlon's strategic
growth plans to significantly increase manufacturing capacity of
all key turbine components, a number of new facilities are
currently planned or under construction. This meets our
objective to vertically integrate the entire supply chain,
ensuring that Suzlon brings to the market the most cost
efficient and reliable technology. It also enables us to control
the supply chain to secure quality, volume and growth, as well
as deliver long term service support.
END TO END SOLUTIONS SINCE 1995
The End-to-End solution pattern is built on Suzlon’s expertise
in technology, processes and thorough understanding of the
wind energy market. It is a unique combination of proven
technology and a bundle of value added services. Under this
successful and proven business model, Suzlon undertakes the
complete turn-key responsibility - from arranging land; to
equipment supply & EPC; to nodal agency clearances; to
life-cycle operations & maintenance of projects. Customers
therefore do not have to engage extra manpower for their
wind projects. Suzlon brought about a paradigm shift in the
wind energy market with the End-to-End solutions. It made
setting up wind energy projects simple, hassle-free and
enabled hundreds of customers including small/medium/big
enterprises, Indian and multinational corporates, public sector
companies and even individuals set-up their own wind energy
projects with confidence and ease.
Under given set of parameter and conditions.
Subject to change without notice due to difference in parameters, conditions and/or change in equipment or technological requirements.